Codings
VCDS CODING
1. Start and stop
[Select]
[09-Cent. Elect.]
[Security Access - 16] (security code: 20113)
[Adaptation - 10]
Channel 34 - Read
Select needed function from below
1. Disable = Reduce 4 from original number (My original number was 12)
2. Enable memory function = 32
3. Inverse start and stop button = 64
Give new value - TEST - SAVE
2. Enable Hidden Menu (Green menu in MMI)
[Select]
[5F - Information Electr.]
[Adaptation - 10] -> Channel 5
Change 0 to 1
Test
Save
[Adaptation - 10] -> Channel 6
Change 0 to 1
Test
Save
Reset MMI = Press Center Knob + upper right + Tone buttons together
Start Hidden Menu = Press Menu + Car
Caution!!!! Keep away from the "Bootloader" (if it appears as an option)
4. VIM
5. Set ACC Default Distace by MMI
Module 13 - Auto Distance Regulation
Select list ACC Basic option (Adaptation - Channel 07 Set to 1)
Reset MMI
In the MMI --> Car > Driver Assistance > Adaptive Cruise --> set the default adaptive cruise distance
MORE
https://www.stemei.de/pages/coding/audi-a8-4h.php
https://forums.ross-tech.com/showthread.php?2642-D4-Audi-A8-VCDS-Codes
6. Audi laptimer, oil temp,. boost gauge activation
Module 17 – Instrument Cluster
Choose procedure 07 – Coding
Read stored value and back it up
Choose Long Coding Helper
Select byte 01 .
Enable box next to bit 03
Save new coding.
Exit
7. Electric tailgate closing with remote control
[6D-Elect. trunk] -> [Security Access – 16] 12345 -> [Adaptation – 10] -> “(4) Activation using rear lid opening button in remote key-Tap function for closing” in the drop-down list --> Set the value to active
8. ACC Basic Settings on the MMI
Activates the display of the basic setting of the Adaptive Cruise Control (ACC) on the MMI. [13 – Dist control] -> [Adaptation – 10] -> Channel 07. Put the value 1. A restart of the MMI is necessary.
9. Automatically activates the electric handbrake when the gear selector is in the "P" position
[53-Parking brake] -> [Security Access – 16] (78713) -> [Adaptation – 10] -> Select "shift to P EPB" in the drop-down list --> Set the value to active
10. Adjust Massage Shut Off Time
– Driver’s Seat] or [89 - Passenger’s Seat], [Adaptation - 10] -> Running Time Of Massage Function, Set the number of seconds you would prefer and click ‘Do It.’
11. Adjust Massage Intensity
[88 – Driver’s Seat] or [89 - Passenger’s Seat], [Adaptation - 10] -> Intensity level (1,2,3,4, or 5) of massage function, Set the intensity(0-100%) you would prefer and click ‘Do It.’
12. Adjust Seat Heat Stepdown Time
[08 HVAC], [Adaptation - 10] -> Time until heated seat power withdrawal stage 3 to stage 2 (or Time until heated seat power withdrawal stage 2 to stage 1), Set the number of minutes you would prefer and click 'Do It.'
13. Adjust Heated Steering Wheel Temperature
[16 – Steering Wheel], [Adaptation - 10] -> Channel-10, Temperature is measured in Celcius, 28 is default
14.Activating Efficiency Mode
Select Control Module 09-Cent.Elect, Select Security/Access - 16, Enter code - 20113 and press Do it, Select Adaptation - 10 Change Channel to 66, Enter new value 47, Click test and note the MMI screen adding the efficiency mode, Click Save and you are done
Disable After-wipe of windscreen wipers
[09 – Cent. Elect.] [Coding - 07] -> Byte 1
Bit 3 - Remove check mark (1 = active)
________________________________________
Disable amber corner lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________
Disable Key warning
[46 – Central Conv.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________
Disable "Lights are on" Warning
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 5
Bit 3 - Set to 0 to disable "lights are on" warning when you open the door.
________________________________________
Disable NAV & Phone warning messages while entering data at speed
[5F - Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________
Disable Seatbelt Chime
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 0
Bit 2-4 – Seat Belt Warning inactive
________________________________________
Adjust Date display
[17 – Instruments]
[Coding - 07] -> Long Code Helper ->
Byte 7 – Use dropdown to select date format
________________________________________
Upshift Display
[17 – Instruments]
[Adaption - 10] -> Upshift Display in center panel ->
Use dropdown to activate/deactivate
(untested)
________________________________________
Enable Adaptive brake lights
[46 - Comfort System] [Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)
__________________________________________
Enable Double Disarm Beep
[46 - Central Conv.] [Adaptation - 10] -> Channel 63
Add 4
________________________________________
Enable/Disable Auto Locking
[46 – Central Conv.]
[Coding - 07] -> Long Code Helper ->
Byte 5 – 0=off/1=on
Bit 4 – Auto lock
Bit 5 – Auto Unlock
________________________________________
Enable DRL to include the following:
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL with Front Side markers
Bit 2 = DRL with High Beams
Bit 3 = DRL with Fog lights
Bit 4 = DRL with LEDs
Bit 6 = DRL with Side markers
Bit 7 = DRL with Tail lights
________________________________________
Enable Euro parking lights that turn on signal at night
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 0 - Set to 1
________________________________________
Enable fog lamp to come on for the same side as that turn signal
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Front Turn Signals as Parking lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
________________________________________
Enable Gauge Test/Needle Sweep
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________
Enable Hidden menu in MMI
[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1
Use this hidden menu at your own risk.
Caution: Keep away from the "Bootloader", if it appears as an option
________________________________________
Enable Import CDs to MMI's HD
[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"
Note: CD must be inserted in player below the mmi, not the changer in the glovebox to be able to rip it.
________________________________________
Enable Independent Fogs control with high beams
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 – (Rear) Uncheck the box or change :Bit 2 to ______________________________________
Enable Remote Operation Windows and Sunroof
[46 - Cent. Conv.] [Coding - 07] -> [Long Coding Helper] Byte 2
Bit 2 - Set to 1
________________________________________________
Enable Release Parking Brake without putting foot on Brake
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 Set to 0
________________________________________
Enable Release Parking Brake without putting seatbelt
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 Set to 0
________________________________________
Enable Reverse mirror tilt
[52 Door Elect, Pass.] -> [Coding - 07] -> [Long Coding Helper] -> Byte 4
Bit 4 and Bit 2 set to 1
________________________________________
Enable VIM on MMI
[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI
________________________________________
Set ADS to specific preset Comfort, Auto, Dynamic or Individual
[09 – Cent. Elect.][Security Access - 16](VCDS will have popup telling you the access code, mine was 20113)
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value. (Uncomfirmed)
________________________________________
Set Headlight washer – Duration (values in milliseconds)
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________
Set Headlight washer – Activation Delay
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 25
change to e.g. 3000
________________________________________
Set Headlight washer – Delay (How many times you can activate the regular washers without activating the headlight washers)
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 25
change to e.g. 3000
________________________________________
Set Coming Home Time– Duration
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 43
change to e.g. 30
________________________________________
Activate/Deactivate Leaving Home Function
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 46
change to 0=off / 1=on
________________________________________
Coming Home – Ambient Light Threshold for activation
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 37
change from 0-7
________________________________________
Enable/Disable Coming Home and Leaving Home Function
[09 – Cent. Elect.]
[Coding - 07] -> Long Code Helper ->
Byte 6 – 0=off/1=on
Bit 1 – Coming Home
Bit 2 – Leaving Home
________________________________________
Enable/Disable Parking Lights
[09 – Cent. Elect.]
[Coding - 07] -> Long Code Helper ->
Byte 9 – 0=off/1=on
Bit 0 – Parking Light Function
___________________________________________
Adjust LED brightness
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3
Set between 5 and 100